! applications: phase-locked loops (pll?s); clock recovery; reference signal tracking; synthesizers; frequency modulation/demodulation ! 8-pin half dil package ! 1.0 to 52.0 mhz frequency range ! 0.5v to 4.5v control voltage ! 25ppm stability ! -40c to 85c operating temperature electrical specifications 2553 n. edgington street, franklin park, il 60131 " phone: 847.451.1000 " fax: 847.451.7585 800-888-1499 or www.champtech.com
1 model K570A frequency range (mhz) input current (ma) 1 to 52 < 26 frequency control function deviation (ppm) minimum maximum 150 linearity (%) 100 modulation bandwidth (3db) nominal control voltage (v) control voltage range (v) transfer function input impedance < 10 > 20khz 2.5 0.5 to 4.5 positive > 50k ? @ 10khz frequency stability (ppm) overall -40 o c to +85 o c 0 o c to +70 o c temperature range ( o c) inclusive of calibration, temperature, voltage, load and aging 25 50 operating storage -40 o c to +85 o c -55 o c to +125 o c supply voltage (v) symmetry (%) cmos/ttl start up time (ms) +5.0v 5% 40/60 <10 typical ssb phase noise (dbc/hz) offset from carrier 10hz -65 100hz 1khz 10khz 100khz -95 -120 -140 -150 (for custom deviation range, vc range, etc. - consult factory) K570A series 5v voltage controlled crystal oscillators part numbering guide K570A xx - specify frequency ?blank? = 0c to 70c operating temp. ?m? = -40c to +85c operating temp. ?a? = 25ppm (0 o c to 70 o c op. temp. only ?b? = 50ppm
pin function voltage control 1 4 5 8 gnd/ & case gnd output + v cc 2553 n. edgington street, franklin park, il 60131 " phone: 847.451.1000 " fax: 847.451.7585 800-888-1499 or www.champtech.com 2 shipping tube cross section output waveform test circuit diagram K570A series 5v voltage controlled crystal oscillators test methods reference procedures description temperature cycle mil-std-833, mtd 1010, cond. b mechanical shock mil-std-883, mtd 2002, cond. b -55c to +125c; air-to-air; 100 cycles; 10 min. dwell vibration mil-std 883, mtd 2007, cond. b 20-2000 hz; 0.06 inch; 15g?s; 3 planes humidity steady state mil-std-202, mtd 103 40c; 90%-95% r.h.; 56 days thermal shock mil-std-883, mtd 1011.7 cond. b electrostatic discharge solderability hermeticity resistance to soldering lead integrity marking permanence life test 100c to 0c; water-to-water; 15 cycles 2 kv to 4 kv threshold solder dip; meniscograph criteria mass spectro. 2 x 10-8 atmos. cc/sec he 260c; 10 seconds: 1 inch/sec. lead tension & bend stress resistance to solvents 1500 g?s mil-std-883, mtd 3015 class ii mil-std-883, mtd 1005.6 mil-std-883, mtd 2022.2 mil-std-883, mtd 1014.8, cond. a1 mil-std-202, mtd 210d, cond. c mil-std-883, mtd 2004.5, cond. a, b1 mil-std-883, mtd 2015.8 125 c, powered, 1000 hours minimum mechanical and environmental specifications
|
